Safety harness with rear anchorage point 3M Protect First Harness

Safety harness with rear anchor point 3M Protect First Harness. Rear anchor point, leg and chest adjustment and standard buckles. D-rings on the back. Weight: 0.95kg

• Profitability, high quality and reliability for work at height
• Large back plate for easy and efficient donning
• Contrast shoulder and leg straps for easy donning Covered ID tags

Supply: 5 to 10 business days

CHARACTERISTICS

• Large back plate

  For easy and efficient placement
• Contrast shoulder and leg straps

  Quick and easy installation
• Covered ID Tags

  Protects tags for the life of the harness

TECHNICAL DATA

Improved webbing:Abrasion resistant and water repellent to reduce the generation of mold and dirt.

Sling hook housings:Avoid having to carry the sling in your hand when not in use.

Comfort pads: On the underside of the shoulder, hip and leg straps. TM® Harness 3M DBI-ROOM

Quick Connect Buckles: Lightweight aluminum alloy buckles for quick and easy connections. (There are also models with a through buckle).

Vertical dorsal D-ring:The vertical dorsal D-ring ensures quick, easy and secure connections to your fall arrest system. Rigid belt: Allows you to carry 27 kg of tools without breaking. Protected Tags: Protected harness tags with hook and hold closure.

INSTRUCTIONS FOR USE - ADJUSTMENT OF THE FALL RESISTANT HARNESS

Before starting. Empty your pockets, as during work or, more importantly, in the event of a fall, items carried in your pockets can become trapped between the webbing of the harness and the user's body, causing injury. Always refer to the instructions for use supplied with the specific harness regarding proper installation and adjustment.

Step one.Begin. Hold the harness by the dorsal D-ring, which is often secured through a D-pad, and make sure the straps are not twisted.

Step two.Shoulder straps. Slide the harness over your arms and place it over your shoulders. Make sure no straps are tangled and they are hanging freely.

Step three.Leg straps. Place it between your legs and hold the leg strap on your left side. Raise the strap between your legs and connect it to the buckle on the left side. Attach the right leg strap using the same procedure.

Step 4.Pectoral straps. Attach the chest strap buckle to the corresponding opposite side buckle.

Paso 5.Waist strap (if equipped). Attach the waist strap buckle to the corresponding opposite side buckle.

Step 6.Adjust the harness so it is tight. Adjust the shoulder straps until they are tight with the adjusters. The left and right sides of the shoulder straps should be adjusted to the same length and the chest strap should be centered on the bottom of the chest, about 15cm below the shoulder. The chest D-ring on the vest harness moves up or down by adjusting the shoulder and leg straps. Center the dorsal D-ring between the shoulder blades. Note: On applicable models the dorsal D-ring can be raised or lowered on the harness webbing as necessary to achieve a correct fit. Re-adjust the leg straps so they are tight. At least 8cm of webbing should remain beyond the buckle on the leg straps. Adjust the waist strap (if equipped).

It's ready!A properly positioned and adjusted full body harness will effectively distribute impact forces throughout your body and provide proper support during suspension and rescue after a fall.

NORMATIVE

EN 361:2003 - Personal protective equipment against falls from a height. Machinery for making pulp of fibrous cellulosic material

EN 365:2005 - Personal protective equipment against falls from height. General requirements for instructions for use, maintenance, periodic review, repair, marking and packaging.

RECOMMENDATIONS FOR ALL EPI

Do not use this safety equipment unless trained by a competent person (this training may be repeated as often as necessary). Please contact CAPITAL SAFETY for information about the classes or if you have any questions about the use of this equipment. (See full instructions for use)

ABOUT 3M

3M Fall Protection, part of the Personal Protection Products division of 3M, has earned a reputation as experts in safe work at height with our market-leading innovations and high-performance rescue and fall protection solutionsThe ultimate protection against falls. What. For more than 75 years, workers at heights around the world have relied on DBI-SALA® products to get their jobs done and home safely. Today, 3M Fall Protection continues that proud tradition by offering high-quality DBI-SALA® fall protection solutions, enabling workers to do their jobs better in a safe and comfortable way.